同城附近人约茶服务联系十,【点击进入立即约茶】

同城附近人约茶服务联系十,【点击进入立即约茶】

Product category
Western Blot-ECL Super Sensitive Luminescent Solution
Ultra sensitive ECL Chemiluminescence Kit

Ultra sensitive ECL Chemiluminescence Kit

  • Product detail
Product introduction
 
ECL chemiluminescence Kit is a high sensitivity chemiluminescence kit, the basic principle is based on luminol ECL chemiluminescence. This product can chemically react with horseradish peroxidase (HRP) conjugated on the secondary antibody to produce fluorescence. Samples are detected by X-ray pressing or other appropriate fluorescence imaging equipment (CCD camera, etc.), and further optimized on the basis of G2014 with higher sensitivity. More stable color rendering, suitable for low abundance target protein detection.
 
 
 
The company currently produces two kinds of ECL chemiluminescence kits, namely G2014 ECL chemiluminescence kit and G2020 ultra-sensitive ECL chemiluminescence kit. For the detection of target proteins with high abundance, such as internal reference proteins, it is recommended to use G2014, which can detect target proteins with a content greater than or equal to 2 ng. For target proteins with low abundance that are difficult to detect, G2020 is recommended. Compared with G2014, the sensitivity of this product is 5 times higher, and pg level protein can be detected with more stable luminescence.
 
 
 
 
 
 
 
Storage and transportation
 
 
 
Wet ice transportation; Stored at 4℃, away from light, valid for 12 months. If it is not used for a long time, it can be stored at -20℃.
 
 
 
 
 
 
 
 
 
Method of use
 
 
 
1. Preparation of ultra-sensitive ECL working fluid: mix ultra-sensitive ECL A and ultra-sensitive ECL B in equal volume, and store at 4℃ under dark conditions. Available now for use within 2 days.
 
 
 
2. In the Western experiment, PVDF membrane was incubated by the second antibody, washed several times, and the excess liquid was sucked out by filter paper. Paste two layers of PE gloves or other transparent films on the exposure box, place the PVDF membrane protein face up between the two layers of the exposure box, add the mixed ECL working solution and cover the film for 1-2 min.
 
 
 
3. Use filter paper or absorbent paper to absorb the ECL working fluid, cover the upper film and begin to press the film.
 
 
 
4. Develop and fix the finished film with developing and fixing reagents (G2019, G2023, G2024 are recommended). Adjust exposure conditions according to luminescence intensity.
 
 
 
 
 
 
 
Matters needing attention
 
 
 
1. The suction head of ultra-sensitive ECL A liquid and ultra-sensitive ECL B liquid must be replaced during the suction process. Mutual contamination of liquid A and liquid B will lead to gradual failure of liquid A or liquid B. Keep sealed after use.
 
 
 
2. If the background is very deep after exposure, the possible reason is that the concentration of the secondary antibody is too high, or the concentration of the primary antibody is too high, or the sealing fluid is not suitable, so change to other sealing fluid.
 
 
 
3. If the fluorescence quenching is rapid, the possible cause is that the fluorescence of the destination strip is too strong, causing HRP to rapidly consume ECL.
 
 
 
4. If there is no luminescence signal, the expression of the target protein may be weak, which may prolong the tablet pressing time.
 
 
 
5. Please wear lab coat and disposable gloves during operation
 
 
 
 
 
 
 
This product is only for scientific research purposes, not for clinical diagnosis!
附近、茶楼、约上门【点击进入立即约茶】、喝茶、品茶、约茶、陪玩、兼职、学生、外围、一次、联系方式、小巷子、小时、随叫随到、约茶官网、风楼平台、同城附近人品茶服务平台【点击进入立即约茶】 、同城约附近人、100、200、300、400、500DIB Data Inventory Biotechnology All rights reserved  粤ICP备2020116600号